Home
Products
Product manuals and datasheets of BSI products.
Downconverter
Provides detailed information and instructions on how to use, operate, assemble, install, troubleshoot, or maintain the Downconverter.
Downconverter Manual
This manual contains safety information and information for installing, configuring, and operating a Downconverter (IDC‑1500, IDC‑2027, IDC‑3239, IDC‑6475).
Downconverter
Maintenance
This chapter describes the maintenance, cleaning, and storage procedures for Real Freedom Downconverters.
Cleaning

Products
Product manuals and datasheets of BSI products.
- Mini-Tx UHD
  Provides detailed information and instructions on how to use, operate, assemble, install, troubleshoot, or maintain the Mini-Tx UHD.
- Real Freedom Receiver
  Provides detailed information and instructions on how to use, operate, assemble, install, troubleshoot, or maintain the Real Freedom Receiver.
- Downconverter
  Provides detailed information and instructions on how to use, operate, assemble, install, troubleshoot, or maintain the Downconverter.
  - Downconverter Manual
    This manual contains safety information and information for installing, configuring, and operating a Downconverter (IDC‑1500, IDC‑2027, IDC‑3239, IDC‑6475).
    - Downconverter
      - Introduction
        The Real Freedom Downconverter is a key component of BSI’s Real Freedom wireless camera system. It receives signals in the broadcast transmit band and down-converts them to a UHF signal of between 50 MHz and 850 MHz. The UHF signal is then fed to a receiver via a coaxial cable.
      - Installation and configuration
        Designed to be compact and fully weatherproof, the Real Freedom Downconverter can be temporarily installed almost anywhere or permanently on the roof of an outside broadcast van.
      - Operation
        Once connected to the system and configured, no further changes are required to the downconverters during the routine operation of the Real Freedom system.
      - Troubleshooting
        This chapter provides troubleshooting information for Real Freedom Downconverters.
      - Maintenance
        This chapter describes the maintenance, cleaning, and storage procedures for Real Freedom Downconverters.
        Routine maintenance procedures
        Cleaning
        Storage
      - Technical data
        Technical drawings, specifications, and connector pinouts for the Real Freedom Downconverter.
      - Safety and regulatory compliance
        Important safety and electromagnetic compatibility information.
  - Datasheet
    The Real Freedom Downconverter receives signals in the broadcast transmit band and down-converts them to a UHF signal of between 50 MHz and 850 MHz. The UHF signal is then fed to a receiver via a coaxial cable.
- Data Transmitter
  Provides detailed information and instructions on how to use, operate, assemble, install, troubleshoot, or maintain the Data Transmitter.
- Fiber Antenna Extender
  Provides detailed information and instructions on how to use, operate, assemble, install, troubleshoot, or maintain the Fiber Antenna Extender.
- Active UHF Splitter
  Provides detailed information and instructions on how to use, operate, assemble, install, troubleshoot, or maintain the Active UHD Splitter
- Fiber Base (Rack Mount)
  Provides detailed information and instructions on how to use, operate, assemble, install, troubleshoot, or maintain the Fiber Base (Rack Mount) unit.
- Camera Back Transmitter
  Provides detailed information and instructions on how to use, operate, assemble, install, troubleshoot, or maintain the Camera Back Transmitter.
- 4K Camera Back Transmitter
  Provides detailed information and instructions on how to use, operate, assemble, install, troubleshoot, or maintain the 4K Camera Back Transmitter.
- VyuSync HEVC Decoder
  Provides detailed information and instructions on how to use, operate, assemble, install, troubleshoot, or maintain the VyuSync Decoder.

Cleaning

If necessary, use low-pressure compressed air cleaning to remove small particles and debris from the surface of a downconverter.

Clean connector surfaces with a cotton swab moistened with a small quantity of alcohol. Use a lint‑free cloth to wipe connector surfaces after cleaning.

CAUTION: Do not use abrasive cleaners.