Home
Products
Product manuals and datasheets of BSI products.
Fiber Base (Rack Mount)
Provides detailed information and instructions on how to use, operate, assemble, install, troubleshoot, or maintain the Fiber Base (Rack Mount) unit.
Fiber Base (Rack Mount) Manual
This manual contains safety information and information for installing, configuring, and operating a Real Freedom Fiber Base (Rack Mount).
Fiber Base (Rack Mount)
Operation
Once connected to the system and configured, no further changes are required to the Real Freedom Fiber Base (Rack Mount) unit during the routine operation of the system.
Fiber base unit rear panel status LEDs
RF1/RF2

Products
Product manuals and datasheets of BSI products.
- Mini-Tx UHD
  Provides detailed information and instructions on how to use, operate, assemble, install, troubleshoot, or maintain the Mini-Tx UHD.
- Real Freedom Receiver
  Provides detailed information and instructions on how to use, operate, assemble, install, troubleshoot, or maintain the Real Freedom Receiver.
- Downconverter
  Provides detailed information and instructions on how to use, operate, assemble, install, troubleshoot, or maintain the Downconverter.
- Data Transmitter
  Provides detailed information and instructions on how to use, operate, assemble, install, troubleshoot, or maintain the Data Transmitter.
- Fiber Antenna Extender
  Provides detailed information and instructions on how to use, operate, assemble, install, troubleshoot, or maintain the Fiber Antenna Extender.
- Active UHF Splitter
  Provides detailed information and instructions on how to use, operate, assemble, install, troubleshoot, or maintain the Active UHD Splitter
- Fiber Base (Rack Mount)
  Provides detailed information and instructions on how to use, operate, assemble, install, troubleshoot, or maintain the Fiber Base (Rack Mount) unit.
  - Fiber Base (Rack Mount) Manual
    This manual contains safety information and information for installing, configuring, and operating a Real Freedom Fiber Base (Rack Mount).
    - Fiber Base (Rack Mount)
      - Introduction
        The Real Freedom fiber system provides unparalleled flexibility of operation. Multiple RF cameras incorporating camera control may be deployed from a single remote site utilizing a single SMPTE hybrid fiber cable.
      - Installation and configuration
        This chapter contains the installation instructions for the Real Freedom Fiber Base (Rack Mount).
      - Operation
        Once connected to the system and configured, no further changes are required to the Real Freedom Fiber Base (Rack Mount) unit during the routine operation of the system.
        Fiber base unit front panel status LEDs
        Fiber base unit rear panel status LEDs
        RF1/RF2
      - Troubleshooting
        This chapter provides troubleshooting information for the Real Freedom Fiber Base (Rack Mount).
      - Maintenance
        This chapter describes the maintenance, cleaning, and storage procedures for the Real Freedom Fiber Base (Rack Mount).
      - Technical data
        Technical drawings and connector pinouts for the Real Freedom Fiber Base (Rack Mount).
      - Safety and regulatory compliance
        Important safety and electromagnetic compatibility information.
- Camera Back Transmitter
  Provides detailed information and instructions on how to use, operate, assemble, install, troubleshoot, or maintain the Camera Back Transmitter.
- 4K Camera Back Transmitter
  Provides detailed information and instructions on how to use, operate, assemble, install, troubleshoot, or maintain the 4K Camera Back Transmitter.
- VyuSync HEVC Decoder
  Provides detailed information and instructions on how to use, operate, assemble, install, troubleshoot, or maintain the VyuSync Decoder.

RF1/RF2

The RF1/RF2 LEDs indicate whether the active splitter is powered and in active (flashing green) or passive (flashing red) mode. In active mode, additional gain is added for splitter loss.

Table 1. RF1/RF2 LED indications
Condition	Description
RED (SLOW FLASH)	PASSIVE SPLIT MODE The splitter unit is powered from the Real Freedom Receiver and is in the passive split state. This is the normal mode of operation which can be controlled from the Real Freedom Receiver.
GREEN (SLOW FLASH)	ACTIVE SPLIT MODE The splitter unit is powered from the Real Freedom Receiver and is in the active split state. The active state introduces extra gain into the system which can be controlled from the Real Freedom Receiver.
OFF	UN-POWERED MODE The splitter unit is not being powered from the Real Freedom Receiver on BNC 1. The splitter will still operate in a passive mode but will not appear on the receiver’s Connection Map.