Home
Products
Product manuals and datasheets of BSI products.
Fiber Base (Rack Mount)
Provides detailed information and instructions on how to use, operate, assemble, install, troubleshoot, or maintain the Fiber Base (Rack Mount) unit.
Fiber Base (Rack Mount) Manual
This manual contains safety information and information for installing, configuring, and operating a Real Freedom Fiber Base (Rack Mount).
Fiber Base (Rack Mount)
Operation
Once connected to the system and configured, no further changes are required to the Real Freedom Fiber Base (Rack Mount) unit during the routine operation of the system.
Fiber base unit front panel status LEDs
RX1/RX2

Products
Product manuals and datasheets of BSI products.
- Mini-Tx UHD
  Provides detailed information and instructions on how to use, operate, assemble, install, troubleshoot, or maintain the Mini-Tx UHD.
- Real Freedom Receiver
  Provides detailed information and instructions on how to use, operate, assemble, install, troubleshoot, or maintain the Real Freedom Receiver.
- Downconverter
  Provides detailed information and instructions on how to use, operate, assemble, install, troubleshoot, or maintain the Downconverter.
- Data Transmitter
  Provides detailed information and instructions on how to use, operate, assemble, install, troubleshoot, or maintain the Data Transmitter.
- Fiber Antenna Extender
  Provides detailed information and instructions on how to use, operate, assemble, install, troubleshoot, or maintain the Fiber Antenna Extender.
- Active UHF Splitter
  Provides detailed information and instructions on how to use, operate, assemble, install, troubleshoot, or maintain the Active UHD Splitter
- Fiber Base (Rack Mount)
  Provides detailed information and instructions on how to use, operate, assemble, install, troubleshoot, or maintain the Fiber Base (Rack Mount) unit.
  - Fiber Base (Rack Mount) Manual
    This manual contains safety information and information for installing, configuring, and operating a Real Freedom Fiber Base (Rack Mount).
    - Fiber Base (Rack Mount)
      - Introduction
        The Real Freedom fiber system provides unparalleled flexibility of operation. Multiple RF cameras incorporating camera control may be deployed from a single remote site utilizing a single SMPTE hybrid fiber cable.
      - Installation and configuration
        This chapter contains the installation instructions for the Real Freedom Fiber Base (Rack Mount).
      - Operation
        Once connected to the system and configured, no further changes are required to the Real Freedom Fiber Base (Rack Mount) unit during the routine operation of the system.
        Fiber base unit front panel status LEDs
        ATTN
        SDI
        RX1/RX2
        FRX
        PWR
        FTX
        Fiber base unit rear panel status LEDs
      - Troubleshooting
        This chapter provides troubleshooting information for the Real Freedom Fiber Base (Rack Mount).
      - Maintenance
        This chapter describes the maintenance, cleaning, and storage procedures for the Real Freedom Fiber Base (Rack Mount).
      - Technical data
        Technical drawings and connector pinouts for the Real Freedom Fiber Base (Rack Mount).
      - Safety and regulatory compliance
        Important safety and electromagnetic compatibility information.
- Camera Back Transmitter
  Provides detailed information and instructions on how to use, operate, assemble, install, troubleshoot, or maintain the Camera Back Transmitter.
- 4K Camera Back Transmitter
  Provides detailed information and instructions on how to use, operate, assemble, install, troubleshoot, or maintain the 4K Camera Back Transmitter.
- VyuSync HEVC Decoder
  Provides detailed information and instructions on how to use, operate, assemble, install, troubleshoot, or maintain the VyuSync Decoder.

RX1/RX2

The RX1/RX2 LEDs indicate whether the fiber base unit's RF1/RF2 interface is communicating with the receiver.

Table 1. RX1/RX2 LED indications
Condition	Description
BLUE	NORMAL STATE The fiber base unit RF1/RF2 interface is communicating with the receiver.
SLOW FLASHING BLUE	ERROR STATE The fiber base unit RF1/RF2 interface is not communicating with the receiver.